{"id":655814,"date":"2025-03-05T20:00:35","date_gmt":"2025-03-05T17:00:35","guid":{"rendered":"https:\/\/en.buradabiliyorum.com\/nanoscale-tweaks-help-alloy-withstand-high-speed-impacts\/"},"modified":"2025-03-05T20:00:35","modified_gmt":"2025-03-05T17:00:35","slug":"nanoscale-tweaks-help-alloy-withstand-high-speed-impacts","status":"publish","type":"post","link":"https:\/\/buradabiliyorum.com\/en\/nanoscale-tweaks-help-alloy-withstand-high-speed-impacts\/","title":{"rendered":"#Nanoscale tweaks help alloy withstand high-speed impacts"},"content":{"rendered":"
\n
\n
\n
\n \"Nanoscale
\n In-situ measurements of microprojectile impact data of NC Cu-3Ta. Credit: Communications Materials<\/i> (2025). DOI: 10.1038\/s43246-025-00757-8
\n <\/figcaption><\/figure>\n<\/p><\/div>\n<\/div>\n

A Cornell-led collaboration devised a new method for designing metals and alloys that can withstand extreme impacts: introducing nanometer-scale speed bumps that suppress a fundamental transition that controls how metallic materials deform.<\/p>\n

The findings, published<\/a> March 5 in Communications Materials<\/i>, could lead to the development of automobiles, aircraft and armor that can better endure high-speed impacts, extreme heat and stress.<\/p>\n

The project was led by Mostafa Hassani, assistant professor in the Sibley School of Mechanical and Aerospace Engineering and in the Department of Materials Science<\/a> and Engineering in Cornell Engineering, in collaboration with researchers from the Army Research Laboratory (ARL). The paper’s co-lead authors were doctoral candidate Qi Tang and postdoctoral researcher Jianxiong Li.<\/p>\n

When a metallic material is struck at an extremely high speed\u2014think highway collisions and ballistic impacts\u2014the material immedia<\/a>tely ruptures and fails. The reason for that failure is embrittlement\u2014the material loses ductility (the ability to bend without breaking) when deformed rapidly. However, embrittlement is a fickle process: If you take the same material and bend it slowly, it will deform but not break right away.<\/p>\n

That malleable quality in metals is the result of tiny defects, or dislocations, that move through the crystalline grain until they encounter a barrier. During rapid, extreme strains, the dislocations accelerate\u2014at speeds of kilometers per second\u2014and begin interacting with lattice vibrations, or phonons, which create a substantial resistance. This is where a fundamental transition occurs\u2014from a so-called thermally activated glide to a ballistic transport\u2014leading to significant drag and, ultimately, embrittlement.<\/p>\n

\n
\n
\n \"Nanoscale
\n As-processed and post-deformed microstructures beneath the surface of a representative nanoindentation impression and a microprojectile impact impression in NC Cu 3-Ta alloys. Credit: Communications Materials<\/i> (2025). DOI: 10.1038\/s43246-025-00757-8
\n <\/figcaption><\/figure>\n<\/p><\/div>\n<\/div>\n

“What you really want in a metallic material is the ability to absorb energy. So one mechanism to absorb energy would be deformation or ductility. In this case, we hope that by suppressing the ballistic transport of dislocations, and, in turn, by preventing the embrittlement, we let the alloy deform, even under a very high rate of deformation, such as those that happ<\/a>en under impact or shock conditions,” Hassani said. “To suppress ballistic dislocation transport and the resulting phonon drag, we use the concept of confining dislocations’ motion, their glide, to nanometer scale.”<\/p>\n

<\/p>\n

Hassani’s team worked with the ARL researchers to create a nanocrystalline alloy, copper-tantalum (Cu-3Ta). Nanocrystalline copper grains are so small, the dislocations’ movement would be inherently limited, and that movement was further confined by the inclusion of nanometer clusters of tantalum inside the grains.<\/p>\n

To test the material, Hassani’s lab used a custom-built tabletop platform that launches, via laser pulse, spherical microprojectiles that are 10 microns in size and reach speeds of up to 1 kilometer per second\u2014faster than an airplane. The microprojectiles strike a target material, and the impact is recorded by a high-speed camera. The researchers ran the experiment with pure copper, then with copper-tantalum. They also repeated the experiment at a slower rate with a spherical tip that was gradually pushed into the substrate, indenting it.<\/p>\n

The biggest challenge, however, was parsing the data. The key was to track the amount of energy used in each impact and indentation. Tang and Li developed a theoretical framework to separate the contributions of the two mechanisms\u2014thermal activation at the low rate, and ballistic transport at the high rate.<\/p>\n

\n
\n
\n \"Nanoscale
\n This laser confocal microscopy reconstruction shows the impression of a spherical microprojectile impact. Credit: Cornell University
\n <\/figcaption><\/figure>\n<\/p><\/div>\n<\/div>\n

“While we are measuring things at high rates\u2014the impact and rebound velocities and particle size\u2014how can we treat the data so that we can really isolate the contribution of dislocation-phonon drag and systematically suppress that contribution?” Hassani said.<\/p>\n

In a conventional metal or alloy, dislocations can travel<\/a> several dozen microns without any barriers. But in nanocrystalline copper-tantalum, the dislocations could barely move more than a few nanometers, which are 1,000 times smaller than a micron, before they were stopped in their tracks. Embrittlement was effectively suppressed.<\/p>\n

“This is the first time we see a behavior like this at such a high rate. And this is just one microstructure, one composition that we have studied,” Hassani said. “Can we tune the composition and microstructure to control dislocation-phonon drag? Can we predict the extent of dislocation-phonon interactions?”<\/p>\n

Co-authors include Billy Hornbuckle, Anit Giri and Kristopher Darling with ARL.<\/p>\n

\n

More information:<\/strong>
\n\t\t\t\t\t\t\t\t\t\t\t\tQi Tang et al, Suppressed ballistic transport of dislocations at strain rates up to 109<\/sup> s\u20131<\/sup> in a stable nanocrystalline alloy, Communications Materials<\/i> (2025). DOI: 10.1038\/s43246-025-00757-8<\/a><\/p>\n<\/p><\/div>\n

\n Provided by
\n Cornell University
\n \t\t\t\t\t\t\t\t\t\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/svg>
\n\t\t\t\t\t\t\t\t\t\t\t\t\t<\/a><\/p><\/div>\n

<\/p>\n

\n

\n Citation<\/strong>:
\n Nanoscale tweaks help alloy withstand high-speed impacts (2025, March 5)
\n retrieved 5 March 2025
\n from https:\/\/techxplore.com\/news<\/a>\/2025-03-nanoscale-tweaks-alloy-high-impacts.html\n <\/p>\n

\n This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no
\n part may be reproduced without the written permission. The content is provided for information purposes only.\n <\/p>\n<\/p><\/div>\n<\/p><\/div>\n